Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Adsorption of Butanol and Water Vapors in Silicalite-1 Films with a Low Defect Density
Stockholm University, Faculty of Science, Department of Materials and Environmental Chemistry (MMK).
Show others and affiliations
Number of Authors: 72016 (English)In: Langmuir, ISSN 0743-7463, E-ISSN 1520-5827, Vol. 32, no 45, p. 11789-11798Article in journal (Refereed) Published
Abstract [en]

Pure silica zeolites are potentially hydrophobic and have therefore been considered to be interesting candidates for separating alcohols, e.g., 1-butanol, from water. Zeolites are traditionally synthesized at high pH, leading to the formation of intracrystalline defects in the form of silanol defects in the framework. These silanol groups introduce polar adsorption sites into the framework, potentially reducing the adsorption selectivity toward alcohols in alcohol/water mixtures. In contrast, zeolites prepared at neutral pH using the fluoride route contain significantly fewer defects. Such crystals should show a much higher butanol/water selectivity than crystals prepared in traditional hydroxide (OH-) media. Moreover, silanol groups ate present at the external surface of the zeolite crystals; therefore, minimizing the external surface of the studied adsorbent is important. In this work, we determine adsorption isotherms of 1-butanol and water in silicalite-1 films prepared in a fluoride (F-) medium using in situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. This film was composed of well intergrown, plate-shaped b-oriented crystals, resulting in a low external area. Single-component adsorption isotherms of 1-butanol and water were determined in the temperature range of 35-80 degrees C. The 1-butanol isotherms were typical for an adsorbate showing a high affinity for a microporous material and a large increase in the amount adsorbed at low partial pressures of 1-butanol. The Langmuir-Freundlich model was successfully fitted to the 1-butanol isotherms, and the heat of adsorption was determined. Water showed a very low affinity for the adsorbent, and the amounts adsorbed were very similar to previous reports for large silicalite-1 crystals prepared in a fluoride medium. The sample also adsorbed much less water than did a reference silicalite-1(OH-) film containing a high density of internal defects. The results show that silicalite-1 films prepared in a F- medium with a low density of defects and external area are very promising for the selective recovery of 1-butanol from aqueous solutions.

Place, publisher, year, edition, pages
2016. Vol. 32, no 45, p. 11789-11798
National Category
Chemical Sciences Materials Engineering
Identifiers
URN: urn:nbn:se:su:diva-137727DOI: 10.1021/acs.langmuir.6b03326ISI: 000388156000009OAI: oai:DiVA.org:su-137727DiVA, id: diva2:1066082
Available from: 2017-01-17 Created: 2017-01-10 Last updated: 2017-11-29Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full text

Search in DiVA

By author/editor
Bacsik, Zoltan
By organisation
Department of Materials and Environmental Chemistry (MMK)
In the same journal
Langmuir
Chemical SciencesMaterials Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 8 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf