Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Tailoring hierarchical structures in selective laser melted materials
Stockholm University, Faculty of Science, Department of Materials and Environmental Chemistry (MMK).
Stockholm University, Faculty of Science, Department of Materials and Environmental Chemistry (MMK). Tsinghua University, China.
Stockholm University, Faculty of Science, Department of Materials and Environmental Chemistry (MMK).
Show others and affiliations
2017 (English)In: IOP Conference Series: Materials Science and Engineering, ISSN 1757-8981, E-ISSN 1757-899X, Vol. 219, article id 012036Article in journal (Refereed) Published
Abstract [en]

With selective laser melting the potential to manufacture a wide variety of geometries from different materials has presented itself. Interest in this technology keeps growing every year, and with that growth a deeper understanding of the process and resulting materials is urgently needed. In this paper we present a short overview of the structural elements that appear during selective laser melting, and explain how to tailor them to achieve specific structures and material properties. Melt-pools, texture and grains, subgrain cells, and inclusions are the elements discussed herein, and tailoring of these elements can have effects on density, and corrosion resistance, as well as mechanical properties in general.

Place, publisher, year, edition, pages
2017. Vol. 219, article id 012036
National Category
Materials Chemistry
Research subject
Materials Chemistry
Identifiers
URN: urn:nbn:se:su:diva-176452DOI: 10.1088/1757-899X/219/1/012036OAI: oai:DiVA.org:su-176452DiVA, id: diva2:1375876
Conference
38th Risø International Symposium on Materials Science, Risø, Norway, 4-8 September, 2017
Available from: 2019-12-06 Created: 2019-12-06 Last updated: 2019-12-09Bibliographically approved
In thesis
1. Additive metallurgy - Thermal influences on structure and properties of stainless steel 316L
Open this publication in new window or tab >>Additive metallurgy - Thermal influences on structure and properties of stainless steel 316L
2020 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Additive manufacturing (AM) as a manufacturing process has, in recent years, become widely accepted as capable of manufacturing parts that will be used in end products. In this thesis, stainless steel grade 316L parts are manufactured using two different powder bed fusion techniques, selective laser melting (SLM) and electron beam melting (EBM). It is recognized that parts made using these processes will have unique microstructures and mechanical properties that have not been seen in bulk parts produced with other methods. The driving force behind the formation of these structures is the fast cooling speed that induces segregation of elements, forming an inhomogeneous microstructure. How these structures react to thermal treatment is less well known and an essential aspect in many applications. Parts manufactured using SLM was treated with hot isostatic pressing (HIP) to investigate if the material retains its unique features. Two different HIP cycles were used, one with 1150 °C and one with 1040 °C. In both cases, the cellular sub-grain structure fades. The cycle utilizing the high temperature is found to coarsen the grain structure and thus lowering the mechanical properties significantly. As manufactured parts show yield strength (615±1 MPa), tensile strength (725±2 MPa) and microhardness (211±10 Hv), compared to values of yield strength (284±2 MPa), tensile strength (636±1 MPa) and microhardness (178±8 Hv) after 1150 °C HIP. Using HIP at 1040 °C, the material will retain a finer grain structure resulting in higher yield strength (417±7 MPa) compared to 1150 °C HIP temperature, while the UTS and hardness have a similar value. It is also observed that the dispersed inclusions formed during SLM are still present after HIP to increase the mechanical properties compared to a conventionally annealed bar (TS: 515 MPa, YS: 205 MPa). Samples manufactured using EBM was investigated to understand the influence of the in-situ heat treatment that is present in the EBM process. The material possesses a long-range heterogeneous structure in addition to the cellular structure, where the cellular structure is present at the top and disappears further down the sample. Samples with different geometries were produced to study the effect of heat flux, cooling speed and the elevated temperature of 800 °C that is present during the EBM process. The thickness of the cell boundaries is measured in different areas, revealing that geometry and size of manufactured parts have a significant impact on the evolving microstructure. It is also revealed that the tensile strength (562±4 MPa) and microhardness (161±11 Hv) is not affected by the change in microstructure, resulting in a very homogeneous material concerning these parameters. Heat treating the material at 800 °C show that the cellular structure becomes diffuse after several hours, but the grain morphology stays the same.

Place, publisher, year, edition, pages
Stockholm: Department of Materials and Environmental Chemistry, Stockholm University, 2020
Keywords
Additive manufacturing, Selective laser melting, Electron beam melting, Hot isostatic pressing, Stainless steel, Microstructural heterogeneity
National Category
Materials Chemistry
Research subject
Materials Chemistry
Identifiers
urn:nbn:se:su:diva-176458 (URN)978-91-7797-968-5 (ISBN)978-91-7797-969-2 (ISBN)
Public defence
2020-02-07, Magnélisalen, Kemiska övningslaboratoriet, Svante Arrhenius väg 16 B, Stockholm, 09:00 (English)
Opponent
Supervisors
Note

At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 5: Manuscript. Paper 6: Manuscript.

Available from: 2020-01-15 Created: 2019-12-09 Last updated: 2020-01-17Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full text

Search in DiVA

By author/editor
Olsén, JonZhong, YuanCui, DaqingShen, Zhijian
By organisation
Department of Materials and Environmental Chemistry (MMK)
In the same journal
IOP Conference Series: Materials Science and Engineering
Materials Chemistry

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf