Iron-doped nickel oxyhydroxides, Nix(Fe1-x)OyHz, are among the most promising oxygen evolution reaction (OER) electrocatalysts in alkaline environments. Although iron (Fe) significantly enhances the catalytic activity, there is still no clear consensus on whether Fe directly participates in the reaction or merely acts as a promoter. To elucidate the Fe’s role, we performed operando X-ray spectroscopy studies supported by DFT on Nix(Fe1-x)OyHz electrocatalysts. We probed the reversible changes in the structure and electronic character of Nix(Fe1-x)OyHz as the electrode potential is cycled between the resting (here at 1.10 VRHE) and operational states (1.66 VRHE). DFT calculations and XAS simulations on a library of Fe structures in various NiOyHz environments are in favor of a distorted local octahedral Fe(III)O3(OH)3 configuration at the resting state with the NiOyHz scaffold going from α-Ni(OH)2 to γ-NiOOH as the potential is increased. Under catalytic conditions, EXAFS and HERFD spectra reveal changes in p-d mixing (covalency) relative to the resting state between O/OH ligands and Fe leading to a shift from octahedral to square pyramidal coordination at the Fe site. XES measurements and theoretical simulations further support that the Fe equilibrium structure remains in a formal Fe(III) state under both resting and operational conditions. These spectral changes are attributed to potential dependent structural rearrangements around Fe. The results suggest that ligand dissociation leads to the C4v symmetry as the most stable intermediate of the Fe during OER. This implies that Fe has a weakly coordinated or easily dissociable ligand that could serve to coordinate the O-O bond formation and, tentatively, play an active role in the Nix(Fe1-x)OyHz electrocatalyst.

The electronic excitation occurring on adsorbates at ultrafast timescales from optical lasers that initiate surface chemical reactions is still an open question. Here, we report the ultrafast temporal evolution of x-ray absorption spectroscopy (XAS) and x-ray emission spectroscopy (XES) of a simple well-known adsorbate prototype system, namely carbon (C) atoms adsorbed on a nickel [Ni(100)] surface, following intense laser optical pumping at 400 nm. We observe ultrafast (∼100  fs) changes in both XAS and XES showing clear signatures of the formation of a hot electron-hole pair distribution on the adsorbate. This is followed by slower changes on a few picoseconds timescale, shown to be consistent with thermalization of the complete C/Ni system. Density functional theory spectrum simulations support this interpretation.

The active chemical state of zinc (Zn) in a zinc-copper (Zn-Cu) catalyst during carbon dioxide/carbon monoxide (CO₂/CO) hydrogenation has been debated to be Zn oxide (ZnO) nanoparticles, metallic Zn, or a Zn-Cu surface alloy. We used x-ray photoelectron spectroscopy at 180 to 500 millibar to probe the nature of Zn and reaction intermediates during CO₂/CO hydrogenation over Zn/ZnO/Cu(211), where the temperature is sufficiently high for the reaction to rapidly turn over, thus creating an almost adsorbate-free surface. Tuning of the grazing incidence angle makes it possible to achieve either surface or bulk sensitivity. Hydrogenation of CO₂ gives preference to ZnO in the form of clusters or nanoparticles, whereas in pure CO a surface Zn-Cu alloy becomes more prominent. The results reveal a specific role of CO in the formation of the Zn-Cu surface alloy as an active phase that facilitates efficient CO₂ methanol synthesis.  

Ketene, a versatile reagent in production of fine and specialty chemicals, is produced from acetic acid. We investigate the synthesis of ketene from acetic acid over the (3,0;1,1) surface of Cu₂O(1 0 0) through analysis of the adsorption and desorption characteristics of formic and acetic acids. The results allow us to establish a reaction mechanism for ketene formation. Observations from x-ray photoelectron spectroscopy (XPS), scanning tunneling microscopy, and temperature programmed desorption (TPD), supported by a comparison with formic acid results, suggest that acetic acid reacts with Cu₂O through deprotonation to form acetate species coordinated to copper sites and hydroxylation of nearby surface oxygen sites. For formic acid the decomposition of adsorbed formate species results in desorption of CO2 and CO while, for acetic acid, high yields of ketene are observed at temperature >500 K. Modeling by density functional theory (DFT) confirms the strong interaction of acetic acid with the (3,0;1,1) surface and the spontaneous dissociation into adsorbed acetate and hydrogen atom species, the latter forming an OH-group. In an identified reaction intermediate ketene binds via all C and O atoms to Cu surface sites, in agreement with interpretations from XPS. In the vicinity of the adsorbate the surface experiences a local reorganization into a c(2 × 2) reconstruction. The total computed energy barrier for ketene formation is 1.81 eV in good agreement with the 1.74 eV obtained from TPD analysis. Our experimental observations and mechanistic DFT studies suggests that Cu₂O can operate as an efficient catalyst for the green generation of ketene from acetic acid.

Controlled electrochemical oxidation of hydrocarbons to desired products is an attractive approach in catalysis. Here we study the electrochemical propene oxidation under operando conditions using Pd L-edge X-ray absorption spectroscopy (XAS) as a sensitive probe to elucidate surface processes occurring during catalysis. Together with ab initio multiple-scattering calculations, our XAS results enable assignment of characteristic changes of the Pd L-edge intensity and energy position in terms of a mechanistic understanding of the selective oxidation of propene. The results, supported by electrochemical density functional theory DFT simulations, show that in the potential range of 0.8–1.0 V vs. the reversible hydrogen electrode (RHE), selective oxidation of propene to acrolein and acrylic acid occurs on the metallic Pd surface. These reactions are proposed to proceed via the Langmuir–Hinshelwood mechanism. In contrast, for the potential range of 1.1–1.3 V vs. RHE, selective oxidation of propene to propylene glycol takes place on a Pd oxide surface.

We compare different means of predicting and rationalizing properties of corrosion films aiming at gaining deeper understanding of the behaviour of copper in aqueous and sulphide-containing environments. Purely geometrical tools ranging from mean bulk information to anisotropic and facet-specific approaches are discussed, and their performances compared against DFT-based stability and property evaluations of a range of interfaces arising from combining low-index crystallographic planes of the compounds Cu, Cu2O, and Cu2S. We demonstrate the necessity to consider facet-specific interactions to understand nanolevel differences between Cu2S and Cu2O film behaviour, and that thin films cannot be directly described by bulk properties.

Corrosion of copper is an expensive degradation process of materials in engineered infrastructures and in various technical applications. It is also an important factor in the geological disposal of spent nuclear fuel, where sulfide-induced corrosion is expected to be the predominant chemical degradation process of copper canisters used for encapsulation and isolation of the radioactive material from the biosphere. One aspect of the corrosion process that is still under intense research is the corrosion morphology and how it might be affected by the composition of the groundwater. Using density functional theory, we investigate the electrochemical interface of corroding copper in aqueous solutions containing sulfides, with and without the presence of Cl-, HCO3-, and SO42- anions. Through state-of-the-art electrochemical models, we account for the effects of pH, concentrations, and potential on the interfacial structure and composition. Results are presented for the Cu(110) surface facet and compared to the (110) and (001) facets of chalcocite (Cu2S), i.e., the main product of sulfide-induced corrosion. It is found that at low potentials, H dominates on all surfaces, and at high potentials, sulfides. In the intermediate ranges, the surfaces differ with sulfides prevailing on Cu, while adsorbed H2O, Cl, or H dominate on Cu2S. The results are summarized as surface Pourbaix diagrams and are generally applicable in corrosion science and electrochemistry. The implications of the study are discussed in light of the expected conditions of planned spent nuclear fuel repositories in Sweden, Finland, and Canada.

Efficient oxygen evolution reaction (OER) electrocatalysts are pivotal for sustainable fuel production, where the Ni-Fe oxyhydroxide (OOH) is among the most active catalysts for alkaline OER. Electrolyte alkali metal cations have been shown to modify the activity and reaction intermediates, however, the exact mechanism is at question due to unexplained deviations from the cation size trend. Our X-ray absorption spectroelectrochemical results show that bigger cations shift the Ni2+/(3+delta)+ redox peak and OER activity to lower potentials (however, with typical discrepancies), following the order CsOH>NaOH approximate to KOH>RbOH>LiOH. Here, we find that the OER activity follows the variations in electrolyte pH rather than a specific cation, which accounts for differences both in basicity of the alkali hydroxides and other contributing anomalies. Our density functional theory-derived reactivity descriptors confirm that cations impose negligible effect on the Lewis acidity of Ni, Fe, and O lattice sites, thus strengthening the conclusions of an indirect pH effect. It is commonly accepted that electrolyte alkali metal cations modify the catalytic activity for oxygen evolution reaction. Here the authors challenge this assumption, showing that the activity is actually affected by a change in the electrolyte pH rather than a specific alkali cation.

Supported metal nanoparticles are essential components of high-performing catalysts, and their structures are intensely researched. In comparison, nanoparticle spatial distribution in powder catalysts is conventionally not quantified, and the influence of this collective property on catalyst performance remains poorly investigated. Here, we demonstrate a general colloidal self-assembly method to control uniformity of nanoparticle spatial distribution on common industrial powder supports. We quantify distributions on the nanoscale using image statistics and show that the type of nanospatial distribution determines not only the stability, but also the activity of heterogeneous catalysts. Widely investigated systems (Au–TiO₂ for CO oxidation thermocatalysis and Pd–TiO₂ for H₂ evolution photocatalysis) were used to showcase the universal importance of nanoparticle spatial organization. Spatially and temporally resolved microkinetic modeling revealed that nonuniformly distributed Au nanoparticles suffer from local depletion of surface oxygen, and therefore lower CO oxidation activity, as compared to uniformly distributed nanoparticles. Nanoparticle spatial distribution also determines the stability of Pd–TiO₂ photocatalysts, because nonuniformly distributed nanoparticles sinter while uniformly distributed nanoparticles do not. This work introduces new tools to evaluate and understand catalyst collective (ensemble) properties in powder catalysts, which thereby pave the way to more active and stable heterogeneous catalysts.

Electrochemically driven CO2 reduction into alcohols and hydrocarbons is a topic of intense study. Photocatalytic approaches, which instead are powered by light, are also reported, but these generally rely on two-component catalysts and yield only moderately reduced products with a single carbon atom. In this report, we use density functional theory, including its linear-response time-dependent implementation, to investigate the feasibility of photocatalytically driving the dimerization of CO chemisorbed on Cu2O, a crucial step in the chemical conversion of CO2 into C-2 products, such as ethanol and ethylene. We find that CO dimerization into OCCO is greatly aided by the photoinduced population of a low-lying LUMO that is bonding with respect to the C-C bond of two adjacently chemisorbed CO molecules.